Products

• 2 oz tube Solarez fiberfil putty
• 2 oz tube Microlite putty
• 60/240 grit sand pad and spreader
• Acetone prep-pad

In a crush-proof watertight plastic capsule.

• 1 oz tube Solarez Epoxy fiberfil putty
• 1 oz tube Microlite Epoxy putty
• 2 60/240 grit sand pads
• Acetone prep-pad

What is Solarez Microlite DUAL CURE Epoxy? It is a white putty made of high-strength UV-Cure resin and super lightweight additives that effectively repair ALL TYPES OF SURFBOARD FOAM, including Styrofoam. This putty cures in roughly 3 minutes by exposure to sunlight or artificial UV light. Or, it can be cured by MEKP catalyst (yes, MEKP) for repairing deep cavities, fin plugs or fin box foundations and other internal structural fillings. It sands and fairs very nicely, making it an easy one-step repair for most any ding. UV-CURE (for superficial dings less than 1/4" deep) 1) Apply in the shade. 2) For easier shaping and faster curing, cover the wet resin with a sheet of clear plastic wrap (Mylar is best). You can easily shape the resin to the contour of the board. 3) Expose to sunlight for 3 minutes 4) Peel off plastic wrap and touch-up sand. DUAL-CURE 1) Into a mixing cup, squeeze out enough Microlite to fill the ding cavity and add 2% Methyl Ethyl Ketone Peroxide (MEKP) catalyst. Mix well. 2) If your ding is very deep, apply a thin layer (1/16") of Microlite all over the interior of the ding. Cure it in the sun for a couple of minutes. 3) Pour the mixture into the ding cavity, cover with a clear plastic sheet. 4) Expose to sunlight. The compound will cure throughout in approximately 5 minutes.

SOLAREZ repair putty is a mixture of clear, non-yellowing, high strength, fiber reinforced polyester resin and an amazing solar activated catalyst. There is no mixing required, just use it right from the tube. It gels in 30 seconds, curing in 3 minutes – but ONLY when exposed to sunlight.

• Proprietary formula assures that millions of fiberglass fibers are thoroughly wet-out and evenly dispersed in every dose.
• Bubble-free mixture
• Denser cross-linking and surface cure
• No residual peroxides
• UV Stable
• Comes with 60/240 grit sand pad.

SOLAREZ repair putty is a mixture of clear, non-yellowing, high strength, fiber reinforced polyester resin and an amazing solar activated catalyst. There is no mixing required, just use it right from the tube. It gels in 30 seconds, curing in 3 minutes – but ONLY when exposed to sunlight.

• Proprietary formula assures that millions of fiberglass fibers are thoroughly wet-out and evenly dispersed in every dose.
• Bubble-free mixture
• Denser cross-linking and surface cure
• No residual peroxides
• UV Stable
• Comes with 60/240 grit sand pad.

SOLAREZ repair putty is a mixture of clear, non-yellowing, high strength, fiber reinforced polyester resin and an amazing solar activated catalyst. There is no mixing required, just use it right from the tube. It gels in 30 seconds, curing in 3 minutes – but ONLY when exposed to sunlight.

• Proprietary formula assures that millions of fiberglass fibers are thoroughly wet-out and evenly dispersed in every dose.
• Bubble-free mixture
• Denser cross-linking and surface cure
• No residual peroxides
• UV Stable
• Comes with 60/240 grit sand pad.

Lightweight, Sandable Filler
Formulated especially for surfboard [urethane] foam repair. For deep dings. Lightweight and easy to sand. Cures either by UV light in approx 3 minutes or by MEKP catalyst in 30 minutes.

Comes with 60/240 grit sand pad and spreader card.

Not for use on Styrofoam (EPS).

• 4 oz “dual-cure” laminating resin
• 2 oz tube Solarez fiberfil putty
• 2 oz tube Microlite putty
• 5″ x 5″ sandpaper in 60, 150 and 320 grits
• Spreader
• 1 oz bottle of acetone
• 200 square inches of 4oz S-glass
• 38″ fiberglass rope
• High-quality stainless steel scissors
• Masking tape
• Catalyst
• Mixing cup
• Stirring sticks
• Razor blade
• Clean-up pads

All in a crush-proof travel box.

Sponge-Rez is a tough, clear, ultra-flexible resin formulated to mend the most common types of catastrophes bodyboards are heir to; worn-out leash anchors, creased bottoms, delaminated decks, hulls or rails, sponge-deck (also known as rash-deck) and semi-fatal gouges. Sponge-Rez works on all types of bodyboard materials including Ethafoam, Surlyn, EVA, Vinyl, and Arcel, however it will melt styrofoam (EPS) cores. Sponge-Rezalso repairs cracked, weathered swim fins. If applied to the fin blades, it increases their stiffness and thrust.

General Directions:

1. Surface should be clean, dry, and free of dirt, and or wax.
2. Use in well ventilated area, preferably outdoors. DO NOT deliberatley inhale vapors – don’t be stupid.
3. Apply liberally on porous surfaces. Use spreader to force Sponge-Rezinto the damged part of the board. Do not apply Sponge-Rez with your fingers.